Top Selling
“DEDECO SUNBURST 2MM RED POLISHING PINS FINE – 400 GRIT”
No matter what the material being worked, SUNBURST POLISHING PINS are the "absolute best" for finishing & polishing hard-to-access areas without removing detail or causing flat spots.
The sharp, clean, specially treated ceramic abrasive grain imbedded throughout their thin flexible rods enable them to work faster and last longer than conventional silicone and polyurethane pins.
SUNBURST POLISHING PINS generate minimal dust and heat and eliminate the need for polishing compound on all precious, semi-precious and non-precious metals.
Recommended operating speeds for most applications is 3,000-18,000 RPM. Lower speeds allow a softer touch, greater flexibility and more subtle results. Higher speeds provide more aggressive material removal. Using the tips of the pin with light pressure maximizes tool life.
Jewelry - Ideal for finishing, smoothing and high-lustre polishing of all precious, semi-precious and non-precious metals, acrylics and ceramics.
“DEDECO SUNBURST 3MM RED POLISHING PINS FINE – 400 GRIT”
No matter what the material being worked, SUNBURST POLISHING PINS are the "absolute best" for finishing & polishing hard-to-access areas without removing detail or causing flat spots.
The sharp, clean, specially treated ceramic abrasive grain imbedded throughout their thin flexible rods enable them to work faster and last longer than conventional silicone and polyurethane pins.
SUNBURST POLISHING PINS generate minimal dust and heat and eliminate the need for polishing compound on all precious, semi-precious and non-precious metals.
Recommended operating speeds for most applications is 3,000-18,000 RPM. Lower speeds allow a softer touch, greater flexibility and more subtle results. Higher speeds provide more aggressive material removal. Using the tips of the pin with light pressure maximizes tool life.
Jewelry - Ideal for finishing, smoothing and high-lustre polishing of all precious, semi-precious and non-precious metals, acrylics and ceramics.
Adentatech System DURO
SYSTEM Duro is a non-precious dental cast alloy for crowns and bridges on cobalt-base, type 5.
SYSTEM Duro is easy to use and quick to polish with excellent laser welding properties. The alloy can be melted by open flame or induction heating. SYSTEM Duro can be used with any commercial, phosphate- bonded investment material (our recommendation: ADENTA®-VEST CB). SYSTEM Duro can be veneered with any high-fusing ceramics.Adentatech System MG
SYSTEM MG is a non-precious dental model cast alloy on cobalt-base, type 5.
SYSTEM MG is suitable for removable partial dentures as well as for all kind of combined works. Easy melting and polishing as well as high mechanical performance are the features of SYSTEM MG. The melting can be done by open flame or inductive heating. For investing we recommend any commercial, phosphate-bonded investment material for model cast (our recommendation: ADENTA®-VEST PA).ANODE ALBILEX (4×3)
In general mixed metal oxide coated titanium anodes consist of a titanium base activated with a coating like rutile structure out of platinum group metal oxides, i.e. mixed with titanium, tantalum or other oxides.
ALBILEX®-MMO-Anodes – used for the electrophoretic coating process Antitarnish-A-100 PRO-KIT - are based on an iridium-tantalum activation, 12.5 g iridium per sqm, titanium mesh type A, with a welded hook.
D&Z CYLINDER BUR CB31
D&Z TAPERED BUR CB33
Dentecon Supercast
SUPERCAST™, High performance non-precious ceramic alloy, with
outstanding quality and excellent bonding strength.
This alloy is designed for the production of high quality porcelain-fused-to-metal restorations.
This alloy has been CAST on over millions of restorations all around the world, it is the most trouble free and user friendly alloy.
DENTECON Thermabond
THERMABOND V™, Fine Grain porcelain users enjoyed using this alloy. This popular alloy has been at international markets for over a decade. Millions of cases have been cast with this alloy all over the world since 1981. It Has won the recognition and confidence of dedicated dental technicians throughout the world.
Dentorium AB210 Cut – Off Wheel
- Dentorium offers an extensive range of laboratory products, which are marketed worldwide, such as Abrasives for Ceramics and Metal and Abrasives for Cobalt-Chromium Alloys. Dentorium has abrasives for metals, ceramics and acrylics – known worldwide for their exceptional quality and low cost. Wide range of formats, sizes and grains, meeting the needs of the most demanding professionals.
Dentorium AB211 Cut – Off Wheel
Dentorium offers an extensive range of laboratory products, which are marketed worldwide, such as Abrasives for Ceramics and Metal and Abrasives for Cobalt-Chromium Alloys.
Dentorium has abrasives for metals, ceramics and acrylics - known worldwide for their exceptional quality and low cost.
Wide range of formats, sizes and grains, meeting the needs of the most demanding professionals.
ELA Carbide Bur Drill C203
ELA Carbide Inverted Burs C2
ELA Steel Burs Cross Cut 038
All burs have a standard shaft diameter of 2.35mm fitting Jewellery Industry standard handpieces. These burs are supplied by Emil Lannge Zahnbohrerfabrik from Germany, founded by Emil Lange Sen. in Engelskirchen in 1919, who were one of the world’s first companies to develop and manufacture carbide-tipped drills in 1953.
Burs are sold individually or multiples of any quantity.
ELA Wheel Burs 3
All burs have a standard shaft diameter of 2.35mm fitting Jewellery Industry standard handpieces. These burs are supplied by Emil Lannge Zahnbohrerfabrik from Germany, founded by Emil Lange Sen. in Engelskirchen in 1919, who were one of the world's first companies to develop and manufacture carbide-tipped drills in 1953.
Burs are sold individually or multiples of any quantity.
Enset Plus System (800100)
The best solution for engraving and crimping with a pneumatic system. It is a digitally controlled system for the engraving of jewelry pieces, system with double port for the connection of two different handpieces.
It has double operating system being able to choose between the original system in which the engraving force is controlled on the panel and the speed of impacts on the pedal or choose the plus mode in which the number of impacts per minute is set on the panel and by means of the pedal the force of the impact on the handpiece is increased with the limit previously set on the panel.
It also has a self-bleeding filter valve to guarantee the good condition of the machine. The system allows a precise engraving and with excellent control of the depth of the cut which allows an excellent brightness in the engraving of gold, silver and precious metals.
The setting control by means of the plus system guarantees absolute control of the impact of the grass on the piece of jewelry that avoids damage to the piece with an undesirable blow on it. It is a very reliable, resistant and small size system.
It is connected to a compressor by means of a plastic hose and the air consumption is very reduced and can also work with a co2 bottle.
ENSET© Compact System (800200)
The Enset© compact pneumatic is the entry model for engraving and crimping on jewelry pieces, its extraordinary power combined with the precision of the electronic foot pedal makes engraving fluid and with excellent control of cutting depth and brightness.
It has a single port for quick connection of the handpiece. It has a filter valve to protect the equipment. In the compact version the pneumatic force is regulated by a wheel on the control panel and is reflected on the integrated pressure gauge. Through the pedal we will increase the number of impulses per minute to transfer the pneumatic force to the handpiece.
The precision of the electronic pedal allows control of engraving and setting, protecting the valuable pieces of precious metals and guarantees the protection of the stone to be set against eventual shocks with the burin or the pearler.
It is a robust machine, simple and intuitive to use, and uniquely compact, taking up very little space on the engraving table. You just need to plug it into the network and the pneumatic compressor and start engraving or engraving.
The air consumption is very low so it can also be used connected to a CO2 bottle.
Eveflexpin Red 72
Eveflexpin Red 73
Golden Eye Saw Blade
Greystar Polishing Compund
Pre-polishing compound for harder metals, removes deeper scratches and freshens up the surface
- Small size compound bar (100x30x15mm)
- Individually packed in DIALUX® branded box
- Adheres well to mops or buffs
- Long lasting, easy to use
- Excellent price - performance ratio